How to Turn a Router Into a Wi-Fi Hotspot- 2 Easy Processes

This vendible explains how to turn a router into a Wi-Fi hotspot. When traveling, many people have wangle to a Wi-Fi router in their hotel rooms or other locations. However, not everyone has their own Wi-Fi hotspot device.

This vendible will explain how to connect an wangle point to a wireless router without a subscription or with a subscription and use CMD prompts. We will moreover trammels how to set up an wangle point with a wireless router and use the old router usefully. Finally, we will requite you the advantages and disadvantages of turning a router into a Wi-Fi hotspot.

In these situations, you can use your home router as a hotspot to get internet wangle on your palmtop or mobile devices.

How to Turn a Router Into a Wi-Fi Hotspot

If you’re familiar with configuring routers and networking in general, you can use the pursuit steps to convert Router B into an wangle point (AP) thus turning a router into a Wi-Fi hotspot. However, if you’re new to networking, it’s recommended that you first read a guide on setting up a home router. Once you finger comfortable, follow the detailed steps below:

1. Cover the WAN (Internet) port on Router B with a piece of tape. This will prevent Router B from functioning as a router, permitting you to use it as an AP instead.
2. Determine the range of IP addresses used by Router A. For example, if Router A’s IP write is 192.168.1.1, its IP range is likely to be 192.168.1.2 to 192.168.1.254.
3. Manually set Router B’s IP write to an unused write within Router A’s range. For example, you can set it to 192.168.1.2. Just make sure that this IP write is not stuff used by any other device.
4. Disable the DHCP function on Router B.

After completing these steps, you can connect Router B to Router A using a network subscription between the LAN ports of both routers. Router B will then function as an AP, providing an improved Wi-Fi range for your devices.

Method 1: Using a Subscription Connection (CMD)

One method involves using a cable to connect the old router to your primary router, and the other method uses a wireless connection. I’ll explain both methods, including using the Writ Prompt (CMD) for the subscription connection. This first method involves connecting the old router to your primary router using an Ethernet subscription and configuring it as a wireless wangle point. Here are the steps:

Step 1: Gather Your Equipment

• Old router: This should be a router you no longer use as your main router.
• Ethernet subscription (usually provided with routers).
• Computer with an Ethernet port.
• Access to the Writ Prompt (CMD).

Step 2: Reset the Old Router (if needed)

If the old router has previously been configured with custom settings, it’s a good idea to reset it to its factory defaults. This typically involves pressing a reset sawed-off on the router for a unrepealable value of time. Refer to your router’s transmission for specific instructions.

Step 3: Connect the Old Router to Your Computer

Plug one end of the Ethernet subscription into one of the LAN ports on your old router and the other end into your computer’s Ethernet port.

Step 4: Wangle the Old Router’s Settings

• Open a Writ Prompt window on your computer. You can do this by pressing Win X and selecting “Command Prompt” or “Windows Terminal” from the menu.
• In the Writ Prompt window, type ipconfig and printing Enter. Squint for the “Default Gateway” IP address. This is typically the IP write of your primary router. Note it down.

Step 5: Wangle the Old Router’s Web Interface

• Open a web browser (e.g., Chrome, Firefox).
• In the write bar, type the Default Gateway IP write you noted in the previous step and printing Enter.
• Log in to the old router’s web interface using the router’s default username and password (usually found on a label on the router). If you don’t have this information, you can often find it online by searching for your router’s model.

Step 6: Disable DHCP on the Old Router

• Once logged in, squint for the DHCP (Dynamic Host Configuration Protocol) settings in the router’s web interface.
• Disable DHCP on the old router. This ensures that it doesn’t mismatch with your primary router’s DHCP.

Step 7: Configure Wireless Settings

• Configure the wireless settings on the old router, including the SSID (Wi-Fi network name) and password. Make sure they are variegated from your primary router’s settings to stave confusion.
• Save your settings.

Step 8: Connect the Old Router to the Primary Router

• Disconnect the Ethernet subscription from your computer.
• Connect one end of the Ethernet subscription to a LAN port on your primary router and the other end to a LAN port on the old router.

Step 9: Test the Wi-Fi Hotspot

• Power on the old router.
• Wait a minute or two for it to marching up and start dissemination the Wi-Fi network.
• On a Wi-Fi-enabled device, scan for misogynist networks, and you should see the SSID you configured on the old router.
• Connect to the Wi-Fi network and test the internet connection.

Method 2: Using a Wireless Connection

Alternatively, you can configure the old router as a wireless wangle point without using an Ethernet cable. Here’s how:

1. Reset the old router to its factory defaults if it has custom settings.
2. Access the old router’s web interface as described in Step 4 of Method 1.
3. Disable DHCP on the old router as described in Step 6 of Method 1.
4. Configure wireless settings (SSID and password) on the old router as described in Step 7 of Method 1.
5. Place the old router in a inside location within the range of your primary router’s Wi-Fi signal but not too tropical to stave interference.
6. Power on the old router and let it unconcentrated the Wi-Fi network.
7. Connect to the old router’s Wi-Fi network using your Wi-Fi-enabled devices, and test the internet connection.

How to create a hotspot using cmd in Windows 7

Creating a Wi-Fi hotspot using the Writ Prompt in Windows 7 involves a variegated set of commands compared to Windows 10 or Windows 11. In Windows 7, you can’t use the netsh wlan set hostednetwork and netsh wlan start hostednetwork commands. Instead, you can use the pursuit steps:

Step 1: Open Writ Prompt as Administrator

• Click the “Start” sawed-off and search for “cmd” or “Command Prompt.”
• Right-click on “Command Prompt” in the search results and segregate “Run as administrator.” This is important considering you need zookeeper privileges to configure the hotspot.

Step 2: Trammels if Your Wireless Connector Supports Hosted Network

Before creating a hotspot, you need to ensure that your wireless connector supports the hosted network feature. You can do this by inward the pursuit writ in the Writ Prompt:

netsh wlan show drivers

Look for the line that says “Hosted network supported.” If it says “Yes,” you can proceed. If it says “No,” your wireless connector does not support this feature.

Step 3: Set Up the Hosted Network

Now, you can create the hosted network with the pursuit command:

Replace NETWORK with the name you want for your hotspot and PASSWORD with the password you want to set for it. For example:

Step 4: Start the Hosted Network

After successfully setting up the hosted network, start it using the pursuit command:

Step 5: Share Your Internet Connection

To share your existing internet connection with the newly created hotspot, follow these steps:

1. Go to the Control Panel.
2. Open “Network and Sharing Center.”
3. Click on “Change connector settings” on the left sidebar.
4. You’ll see a list of network connections. Right-click on the network connection that has internet wangle (e.g., your Ethernet or Wi-Fi connection) and select “Properties.”
5. Go to the “Sharing” tab.
6. Check the box that says “Allow other network users to connect through this computer’s internet connection.”
7. In the drop-down menu below, select the network connection you just created (the hosted network) from the list.
8. Click “OK” to save your settings.

Step 6: Connect to Your Hotspot

Your hotspot is now set up and ready to use. Other devices can connect to it using the SSID and password you specified earlier.

Remember that in Windows 7, you’ll need to manually start the hosted network using the netsh wlan start hostednetwork writ every time you want to use it, and stop it using the netsh wlan stop hostednetwork writ when you’re done

Conclusion

Repurposing an old router as a Wi-Fi hotspot can be a cost-effective and practical solution to proffer your network coverage or provide internet wangle in areas with weak connectivity. Whether you segregate the method involving an Ethernet subscription connection or utilize the Writ Prompt in Windows 7, the process allows you to outbreathe new life into outdated hardware.

By configuring the router correctly and taking wholesomeness of its wireless capabilities, you can enhance your home or office network and provide a reliable Wi-Fi signal to meet your connectivity needs.

Whether you’re looking to modernize internet accessibility in remote corners of your space or simply looking to make the most of your existing resources, transforming an old router into a Wi-Fi hotspot is a valuable skill that can goody both tech enthusiasts and everyday users alike.

FAQS